Page 29 - featured

Interested in purchasing this awesome oil cooler system? Check out our product page for more details!

Mishimoto Ford Fiesta ST Oil Cooler Kit

Testing time! It's always fun to see the results when you make changes to your vehicle, whether bolting on a new wheel and tire combo, or installing a  new set of  dampers. In this case, we are expecting our Fiesta ST oil cooler setup to drop fluid temperatures by a substantial margin during our on-road testing.

Testing Setup and Conditions

Testing the stock Fiesta ST oil cooler is relatively simple. Only one temperature and pressure will need to be monitored, so we can utilize our sandwich plate sensor adapter shown below.

Interested in purchasing our BRZ/FR-S Fan Shroud Kit? Check out more details at the link below!

Mishimoto Subaru BRZ / Scion FR-S / Toyota GT86 Plug-N-Play Aluminum Fan Shroud Kit!

We're back for some more fan shroud fabrication! The last portion of this series highlighted the beginning stages of initial shroud design. The BRZ/FR-S uses a fairly unique overflow tank that mounts directly to the factory fan shroud. This is our first target for part two of product design.

Overflow Tank Mount Fabrication

This tank has two upper mounting points which use a bolt which passes through the tank material and into threads on the shroud. We utilized round stock aluminum which was cut to the proper length, drilled, and tapped for the appropriate factory bolt. These were then welded to the shroud in a position that would place the tank in the

Interested in purchasing our awesome intake system? Check out our product page linked below!

Mishimoto Nissan 350Z Performance Air Intake!

We're back with more grinding, fitting, cutting, and welding. The fabrication of our intake prototype for the Nissan 350Z continues!

Airbox Fabrication

When we left off, we had fabricated three sides of our airbox and created a 3D model for our MAF-to-filter adapter. The next plan was to continue designing and constructing our airbox, starting with the base.

Template for 350Z intake airbox base

We mapped out our base

Interested in purchasing our 6.0L intake elbow?

If you are familiar with our brand, you know we have a vast product line of heat exchangers and associated products available for the Ford 6.0L Powerstroke. We've had great feedback from our customers about our existing products as well as the new products they would like to see come out of our garage. Now that we have our own 6.0L shop truck (shown below), we have easy access to a vehicle for product development and test fitting.

Mishimoto 6.0L shop truck

We decided to come up with our own rendition of an inexpensive, free-flowing intake elbow for the 6.0L. Yes, we realize there are ample options currently on the market. That said, we would like our design

First Prototype: Sound

We're starting this article with a recap of Part 1 of this series, which highlighted our first prototype for the 2015 Mustang EcoBoost exhaust design. If you recall, this design featured a midmuffler as well as two rear mufflers.

We promised a sound clip of our first design, so check it out below!

As you can hear, this setup is not quite what we are looking for. Although our mufflers are more free-flowing compared to the stock units, the sound of the EcoBoost is still stifled quite a bit. In fact, actual noise increases over the stock exhaust setup are minimal and nearly unidentifiable.

We needed to make some modifications to create a more prominent sound. Back

After removing both catch cans for data collection in our previous post, we discussed the idea of relocating the bracket that holds the PCV catch can to a different area in the engine bay. We mentioned earlier that we were toying with the idea because the current location of the Fiesta ST catch can raised some concerns. One of them being that the current location for the catch can would interfere with right-hand drive (RHD) applications of the Fiesta ST, and we want this catch can to be all inclusive. In addition, it came to our attention later on that it would also interfere with some aftermarket intakes.  We try to take common Fiesta ST parts upgrades into consideration so that the products we make will fit all Fiesta STs. The consensus was that because there was a bit more room further forward in the engine bay to relocate the catch can, that would be the way to go.

Bracket and Hose Setup

With this new location in mind our engineers began fabricating a

Interested in purchasing our F30 intake system? Check out our product page for more information!

Mishimoto BMW F30 Performance Intake!

With testing and data collection complete, we assembled our final prototype BMW F30 air intake to confirm that the full kit fits flawlessly prior to starting production. We have been pretty excited to see this unique kit come together. Check it out in its final form!

Final Intake Images

Our final prototype BMW F30 intake was cut from a sheet of metal using a waterjet. Once we had the template cut to our drawing and model specs, we bent each piece appropriately.

First, the base of our airbox.